AdvanSix - Aegis PIR-H120ZP - PA 6

Enhanced TDS

Identification & Functionality

Chemical Family: Polyamides
Polymer Name: Polyamide 6 (PA 6)
Plastics & Elastomers Functions: Resin
Technologies: Plastics
Product Families: Plastics — Basic Thermoplastics
Recycled Polymers
Plastics — Engineering & Specialty Polymers
Polyamides

Features & Benefits

Labeling Claims: Contains PIR Resin,
Recycled,
Sustainable
Materials Features: Chemical Resistant,
Excellent Strength,
Good Abrasion Resistance,
Good Processability,
Good Toughness,
Heat Resistance,
High Performance,
High Viscosity

Applications & Uses

Properties

Thermal Properties


	Value	Units	Test Method / Conditions
Melting Point	220 (428)	°C (°F)	ASTM D-3418

Typical Properties


	Value	Units	Test Method / Conditions
Density	1.13	g/cmᵌ	ASTM D-792
Extractable Content	max. 0.8	%	SOP-702-307
Melt Flow Rate (at 235°C/1.0 kg or 455°F/1.0 kg)	1.9	g/10 min	ASTM D-1238
RV (at 96% Sulfuric Acid)	3.6	-	-
Viscosity FAV	120	-	ASTM D-789

Gas Barrier Properties


	Value	Units	Test Method / Conditions
Carbon Dioxide Permeability (at 23°C (73°F), 100% RH)	72.8 (4.7)	cc.25μm/m²/day (cc.mil/100 in²/day)	ASTM D-1434
Nitrogen Permeability (at 73°F (23°C), 80% RH)	14.0 (0.9)	cc.25μm/m²/day (cc.mil/100 in²/day)	ASTM D-1434
Oxygen Permeability (at 73°F (23°C), 0% RH)	40.3 (2.6)	cc.25μm/m²/day (cc.mil/100 in²/day)	ASTM D-1434
Water Vapor Permeability (at 100°F (38°C), 100% RH )	992 (64)	gm.25μm/m²/day (gm.mil/100 in²/day)	F-1249

Moisture Properties


	Value	Units	Test Method / Conditions
Moisture (24 Hour)	1.6	%	ASTM D-570
Moisture (50% RH)	2.7	%	ASTM D-570
Moisture (Saturation)	9.5	%	ASTM D-570
Moisture Content	max. 0.08	%	ASTM D-6869

Regulatory & Compliance

Certifications & Compliance: EC Regulation 2011/10,
EU Compliant,
FDA 21 CFR 177.1500,
FDA 21 CFR Regulations

Technical Details & Test Data

Extrusion Guidelines

Melt Viscosity vs. Temperature

Melt Temperature: 220°C (428°F)
Melt Temperature Range: 232°C (450°F) to 271°C (520°F).
Two key factors affect the melt viscosity (stiffness or fluidity of the melt):
1. The molecular weight (Mw) of the resin: Higher Mw resins will have a higher melt viscosity than lower Mw resins.
2. Temperature of the melt for any given Mw resin: Higher process temperatures will provide a more fluid melt viscosity than lower process temperatures.

Typical Barrel Profile for Cast Films

Barrel: 230-260°C (446-500°F)
Adapter: 260-266°C (500-510°F)
Die: 260°C (500°F)
Process Melt Temperature: 260-270°C (500-518°F)

Typical Barrel Profile for Tubular (Blown) Films

Barrel: 246-254°C (474-490°F)
Adapter: 260°C (500°F)
Die: 254°C (490°F)
Process Melt Temperature: 254-260°C (490-500°F)

Screw Parameters

Metering Section: 40%
Transition Section: 3 to 4 flights
Feed Section: Balance of screw length
Compression Ratio: 3.5:1 to 4.0:1
L/D Ratio: 24:1

Metering Section Flight Depth

Screw Diameter	Recommended Depth
1"	0.055"
1.5"	0.060"
2"	0.070"
2.5"	0.080"
3.5"	0.100"
4.5"	0.115"
6"	0.135"

Note: The values in this data sheet are for natural color resins only. Colorants or other additives may alter some or all of these properties. The data listed here fall within the normal range of product properties, but should not be used to establish specification limits nor used alone as the basis of design.

Storage & Handling

Processing Guidelines: Material Handling

Aegis® PIR-H120ZP is supplied in sealed containers and drying prior to processing is not required. However, higher moisture is the primary cause of processing issues. If drying becomes necessary, a dehumidifying or desiccant dryer operating at 80°C (176°F) is recommended. Drying time is dependent on moisture level. More information about safe handling procedures can be obtained by requesting the Safety Data Sheet.